Toyota Camry

1992-1997 of release

Repair and operation of the car



Kamri's Toyota
+ General data
+ 1. Maintenance
+ 2. Engine
+ 3. Six-cylinder V6 engines
+ 4. Capital repairs of engines
+ 5. Cooling and heating
+ 6. Fuel system
+ 7. System of ignition
+ 8. Toxicity decrease
+ 9. Transmission
+ 10. Automatic transmission
+ 11. Coupling and power shafts
- 12. Brake system
   12.2. General information
   12.3. Anti-blocking system of brakes (ABS)
   12.4. Replacement of brake shoes of disk brakes
   + 12.5. Support of disk brakes
   + 12.6. Brake disk
   12.7. Replacement of brake shoes of drum brakes
   + 12.8. Working brake cylinder
   + 12.9. Main brake cylinder
   12.10. Brake pipelines and hoses
   12.11. Pumping of hydraulic brake system
   + 12.12. Vacuum amplifier of brakes
   12.13. Replacement of brake shoes of the emergency brake on back disk brakes
   + 12.14. Adjustment of the parking brake
   + 12.15. Replacement of a cable of the emergency brake
   + 12.16. Stoplight switch
+ 13. Suspension bracket
+ 14. Body
+ 15. Electric equipment


12.13. Replacement of brake shoes of the emergency brake on back disk brakes

GENERAL INFORMATION

Preventions

Surely make replacement of all blocks even if the limit of wear were reached by one block.

During the work of brake shoes brake dust which contains asbestos, unhealthy therefore when cleaning brake shoes do not use compressed air is formed and do not inhale dust.


Details of the emergency brake on back disk brakes

1 – brake disk;
2 – spring;
3 – spring clamps;
4 – spring;
5 – adjusting level;
6 – front brake shoe;
7 – pin;
8 – plate;
9 – spring;
10 – rack of blocks;
11 – laying;
12 – back block;
13 – pin;
14 – springs;
15 – back support;
16 – stopper;
17 – fastening bracket;
18 – lever of the emergency brake

PERFORMANCE ORDER
1. Remove a brake disk.
2. Measure thickness of brake shoes. If thickness of an overlay of a brake shoe less than 0,8 mm, brake shoes need to be replaced.
3. Remove a nave and the bearing of a nave.
4. Using special liquid, clear brake shoes. 5. Disconnect a returnable spring of a back brake shoe from an anchor finger. 6. Disconnect a returnable spring from a back brake shoe.
7. Remove a returnable spring of a front brake shoe from an anchor finger. 8. Remove a returnable spring from a front brake shoe. 9. Remove a plate of a spring of fixing of a back brake shoe, pressing a plate and turning it on 90 °.
10. Remove a rack of blocks from the top part of brake shoes. 11. Remove a plate of a spring of fixing of a forward block, pressing a plate and turning it on 90 °.
12. Remove regulirovoch a ny level and the lower returnable spring.
13. Remove a bracket of fastening of a hinged finger from a back brake shoe. 14. Remove the lever of the emergency brake from a back brake shoe. 15. Apply a layer of high-subjects of peraturny greasing on a brake board in places of contact of a board with blocks.
16. Install the lever of the emergency brake on a back brake shoe and record a bracket. 17. Fix a returnable spring from a reverse side of a back brake shoe. 18. Fix a returnable spring from a reverse side of a front brake shoe.
19. Establish regulirovoch a ny level between brake shoes. 20. Establish brake shoes on a brake board and establish a rack of blocks and a spring. 21. Establish a returnable spring of a front brake shoe.
22. Establish a returnable spring of a back brake shoe. 23. Establish a spring and a clamp of a back brake shoe. 24. Establish a spring and a clamp of a front brake shoe.
25. The correct arrangement of details of the emergency brake on a brake board.
26. Establish a brake disk.
27. Take a stopper from an adjusting opening of a brake disk. Rotating a screw-driver a wheel of an adjusting level, part brake shoes so that it was possible to remove a brake disk without jamming.
28. Further installation is made in sequence, the return to removal.