Toyota Camry

1992-1997 of release

Repair and operation of the car



Kamri's Toyota
+ General data
+ 1. Maintenance
+ 2. Engine
+ 3. Six-cylinder V6 engines
+ 4. Capital repairs of engines
+ 5. Cooling and heating
+ 6. Fuel system
+ 7. System of ignition
+ 8. Toxicity decrease
+ 9. Transmission
+ 10. Automatic transmission
+ 11. Coupling and power shafts
- 12. Brake system
   12.2. General information
   12.3. Anti-blocking system of brakes (ABS)
   12.4. Replacement of brake shoes of disk brakes
   + 12.5. Support of disk brakes
   + 12.6. Brake disk
   12.7. Replacement of brake shoes of drum brakes
   + 12.8. Working brake cylinder
   - 12.9. Main brake cylinder
      12.9.2. Repair
      12.9.3. Installation
   12.10. Brake pipelines and hoses
   12.11. Pumping of hydraulic brake system
   + 12.12. Vacuum amplifier of brakes
   12.13. Replacement of brake shoes of the emergency brake on back disk brakes
   + 12.14. Adjustment of the parking brake
   + 12.15. Replacement of a cable of the emergency brake
   + 12.16. Stoplight switch
+ 13. Suspension bracket
+ 14. Body
+ 15. Electric equipment


12.9.2. Repair

GENERAL INFORMATION

Details of the main brake cylinder (above without ABS, below with ABS)
1 – case of the main brake cylinder;
2 – sealing ring;
3 – screw of fastening of a tank of brake fluid;
4 – stopper;
5 – mesh filter;
6 – tank of brake fluid;
7 – sealing ring;
8 – lock ring;
9 – piston and spring No. 1;
10 – piston and spring No. 2;
11 – laying;
12 – lock bolt;
13 – lock bolt;
14 – laying;
15 – sealing ring;
16 – screw of fastening of a tank of brake fluid;
17 – stopper;
18 – mesh filter;
19 – tank of brake fluid;
20 – sealing ring;
21 – lock ring;
22 – piston and spring No. 1;
23 – piston and spring No. 2;
24 – case of the main brake cylinder

PERFORMANCE ORDER
1. Unscrew a bolt of fastening of a tank. 2. Remove a tank of brake fluid and sealing rings.
3. Fix the main brake cylinder in a vice and, using the corresponding mandrel, press main thing pistons tormozno go the cylinder against the stop and unscrew a lock bolt.
4. Remove a lock ring in an end face of the main brake cylinder.
5. Take pistons and springs from the case of the main brake cylinder.
6. Wash out all details of the main brake cylinder in brake fluid and check a condition of details. Before ustan which details in the main brake cylinder previously grease them with pure brake fluid.
7. Install pistons with springs in the main brake cylinder, move them against the stop forward and screw up a lock bolt.
8. Establish a new lock ring in back part of the main brake cylinder.
9. Install sealing plugs of a tank of brake fluid, a tank and fix a tank the screw.
10. Before installation of the main brake cylinder fill in in it brake fluid and remove air for what fix the main brake cylinder in a vice and close exhaust outlets of the main brake cylinder carving traffic jams.
11. Fill in pure brake fluid in a tank.
12. Unscrew one stopper and, moving the piston in the main brake cylinder, squeeze out from it air.
13. Before an otpuskaniye of the piston screw in into place a carving stopper.
14. Repeat operation on removal of air until the opening does not leave only pure brake fluid without vials of air. Repeat operation on removal of air from the main brake cylinder on the second exhaust outlet.