Toyota Camry

1992-1997 of release

Repair and operation of the car



Kamri's Toyota
+ General data
+ 1. Maintenance
+ 2. Engine
+ 3. Six-cylinder V6 engines
- 4. Capital repairs of engines
   4.2. General information
   4.3. Check of a compression
   4.4. Recommendations about removal of the engine
   + 4.5. Removal and installation of the engine
   4.6. Sequence of dismantling of the engine
   4.7. Dismantling of a head of the block of cylinders
   + 4.8. Cleaning and survey of a head of the block of cylinders
   4.9. Assembly of a head of the block of cylinders
   4.10. Removal of pistons with rods
   4.11. Removal of a cranked shaft
   + 4.12. Block of cylinders of the engine
   4.13. Pistons and rods
   4.14. Cranked shaft
   + 4.15. Survey and choice of radical and shatunny bearings
   4.16. Control of a side play of assembly of the balance weight (engine 5S-FE)
   4.17. Balance of assembly of the engine at capital repairs
   4.18. Installation of piston rings
   - 4.19. Installation of a cranked shaft and check of working gaps of bearings
      4.19.1. Check of a working gap of the bearing
      4.19.2. Final installation of a cranked shaft
   4.20. Installation of a back sealing ring of a cranked shaft
   4.21. Installation of pistons and rods, check of working gaps of bearings
   4.22. Installation of assembly of the balance weight (engine 5S-FE)
   4.23. Start of the engine after capital repairs
+ 5. Cooling and heating
+ 6. Fuel system
+ 7. System of ignition
+ 8. Toxicity decrease
+ 9. Transmission
+ 10. Automatic transmission
+ 11. Coupling and power shafts
+ 12. Brake system
+ 13. Suspension bracket
+ 14. Body
+ 15. Electric equipment


4.19.1. Check of a working gap of the bearing

GENERAL INFORMATION

Sequence of a tightening of bolts of fastening of covers of radical bearings on chetyrekhts the lindrovy engine

Sequence of a tightening of bolts of fastening of covers of radical bearings on the engine 3VZ-FE

Sequence of a tightening of bolts of fastening of covers of radical bearings on the engine 1MZ-FE

Sequence of a tightening of lateral bolts of fastening of covers of radical bearings on the engine 1MZ-FE

Screwing up of bolts of fastening of covers of radical bearings on the V6 engine

PERFORMANCE ORDER
1. Clear back part of inserts and a place of their installation in the block of cylinders and covers of radical bearings.
2. Install inserts on the places in the block of cylinders of the engine.
3. One of methods which assumes existence of a micrometer for measurement of diameter of openings (see item 4), consists in establishing covers of radical bearings together with inserts on the block of cylinders and to screw them the demanded moment. Measure the internal diameter of each collected couple of inserts of bearings. Measure diameter of each radical neck of a cranked shaft. Subtract the corresponding diameter of a radical neck of a cranked shaft from the measured diameter of the bearing.
4. The second (and more exact) the method consists in using the product known as Plastigage. It is round plastic a sovy core which contracts between an insert and a neck of a cranked shaft. After removal of a cover of the radical bearing the deformed plastic core is measured by a special template which is available in Plastigage set. Procedure for use of Plastigage following.
4a. On the inserts installed in the block of cylinders establish a cranked shaft without greasing. Necks of a cranked shaft and inserts have to be absolutely pure and dry.
4b. Cut off some slices of a plastic core of Plastigage (they have to be slightly shorter, than width of the main bearings) and establish on each neck of a cranked shaft.
4v. Establish covers with the lower inserts and tighten fastening bolts the demanded moment. In the course of measurement of a gap by Plastigage method do not rotate a cranked shaft (see rice. Sequence of a tightening of bolts of fastening of covers of radical bearings on chetyrekhts the lindrovy engine, Sequence of a tightening of bolts of fastening of covers of radical bearings on the engine 3VZ-FE, Sequence of a tightening of bolts of fastening of covers of radical bearings on the engine 1MZ-FE, Sequence of a tightening of lateral bolts of fastening of covers of radical bearings on the engine 1MZ-FE).
4g. Unscrew a cover of fastening of an insert, remove it and apply a large-scale ruler to the deformed plastic core. Comparing width of the deformed plastic core to control width on a large-scale ruler, determine gap size.
4d. In end carefully clear Plastigage-material traces from inserts and a cranked shaft.